This is the industry's leading TV antenna signal meter. Want to get the most TV antenna broadcast channels in your area? This TV antenna signal meter will help you locate and lock onto all available channels faster and easier. Look no further than the Digiair Pro!
Signal strength is presented on the LCD-display. In analog mode it shows a single channel or six channels at the same time. You can also choose to view the signal in spectrum mode. In digital mode it displays the BER (bit error rate) and SNR (signal/ noise ratio). Readout of UCB (uncorrected bits) and CB (corrected blocks) is also easy to do. Furtermore DIGIAIR Pro present pitchtones (the higher tone the stronger signal) on a loudspeaker. DIGIAIR Pro is very sensitive and can detect even the weakest signals. DIGIAIR Pro can feed Voltage (5/12 Volt) to external active antennas this feature is short-circuit protected by an automatic fuse. DIGIAIR Pro is charged via an external DC power-source of 13,5 -18 volt. Even though the DIGIAIR Pro has a lot of functions it is still very easy to use and has a very compact design. DIGIAIR Pro operates with 8xAA rechargeable batteries. The unit will works for at least 2 hours with fully charged batteries
Input Frequency: 47-862MHz
Input Level: 25-100dBuV
Input Impedance: 75 Ohm, F-connectors
Shows a single channel or six channels at the same time. You can view signal in spectrum mode.
SATlink WS-6923 Digital Satellite Signal Finder, Support DISEQC 1.0/1.1 ,0/22khz Tone, Black
Features:* Digital meter for signal strength and quality* Sound and Light Alarm for Locking Signal* Auto Calculate Angle of AZ ,EL* Supports DISEQC 1.0/1.1 ,0/22khz Tone* Beep Integrated* LNB short protect* Software upgrade via USB port* Easy to carryTechnical Specifications:TRANSMISSION STANDARDS: DVB-SSATELLITE INPUT/DEMODULATIONConnector Type: F TypeInput Frequency: 950 to 2150 MHzSignal Input Level: - 65 to -25 dBmBand Switch Control: 22KHzLNB Supply: 13V/18V, IMax300mADemodulation Type: QPSKSymbol Rate: 2
SMAKN® DDS Signal Generator Module AD9833 Sine Square Wave
D9833 is a low-power, frequency programmable sine, triangle and square wave generator. Waveform generator widely used in a variety of measurements, such as the field of motivation and time-domain response. Output signal frequency and phase are programmable, so that the output signal frequency and phase is very easy to adjust. Do not need any external devices. Frequency registers 28BIT bit, if the base frequency input 25MHZ, the smallest output precision 0.1HZ. Similarly, if the reference frequency input 1MHZ, the smallest output precision 0.004HZ. Packages: 1 x AD9833 DDS Signal Generator Module
Discover satellites with ease with the Satellite Finder Meter. The pocket satellite finder features a highly sensitive illuminated meter. With a built-in miniature lamp and buzzer, the device has 75_, 950 MHz-2,250 MHz input. With 13V-18V DC power requirements, the meter has a -40 dBm-10 dBm input level. ;;
Satellite Signal Strength Meter Finder Squawker Finder Locator Tester, Dish Network, 2 GHz, 13 - 18 VDC, 75 Ohm
Get perfect satellite dish reception in seconds with this easy-to-use DSS Satellite Finder! This tool is a must for RV / motor home enthusiasts who take a satellite dish with them on the road, OR for home users. This indispensable product lets you easily make adjustments yourself, without having to shout back and forth with a second person at the TV location
First Strike Meters FS1 Pro HD Digital Satellite Finder
If you have always wanted a professional satellite finder meter but didn't want to pay the "BIG BUCKS", this is the meter for you. First Strike Meters are made for the professional but are easy for the Novice to understand and use. No more searching through complicated menus to find the setting you need to change. All parameters show on one screen making it easy for the user to modify any setting. Don't let the price fool you, the FS1 First Strike satellite finder meter will give you all the signal measurements that you need to install or re-align your satellite dish at a price you can afford. FS1 quickly and easily finds even weak signals. Unlike the competitors meters, you can do a sweep of the dish to find the signal. Uses the same type display screen as cell phones so it can be read in direct sunlight. Display screen has a switchable back light so your meter can be used in low light conditions. FS1 has a Global Data Bank that holds all the satellites in a separate data bank. The meter also has a User Defined Data Bank that stores 100 satellites. Entries in the Global Data Bank can be copied to the User Defined Data Bank and then easily edited to fit your needs. The user can define new entries from the keypad. Meter never needs to be returned for re-calibration due to the unique calibration system built in to the meter. Each time the meter boots up it automatically calibrates for optimum performance so you can align each install with confidence. Rechargeable Li-on battery lasts approximately 3.5 hours on a full charge. If the battery runs low during use, you can loop the satellite receiver through the meter and power the meter from the satellite receiver power supply. Meter housing has a battery door for easy access and replacement of the battery. Comes with a "Ruff Neck" protective jacket to protect your meter on the job. Universal charger operates on 120vac/60Hz or 220vac/50Hz making it usable anywhere. Easy change power plug.
Trimax SM-4500 Digital Satellite Meter FTA Dish Network DTV
For the first time in a economical digital meter, you are able to view the actual channel on the screen of the meter. Now you can quickly and accurately align the satellite AND you can instantly check the stability of the channel right on the screen of the meter.
In this model we have eliminated the troublesome 'register code'. You will no longer need the code when resetting your meter.
Transponders, Frequency, Symbol Rate, Polarity, and other settings can be modified by the user. There is never a need to send your meter in for a upgrade.
English, Italian, Portuguese, Turkish, Swedish, Spanish, Deutsch, French, Dutch, Finnish, Arabic, Denish, Russian, Czech, Greek, Lietuva.
Meter never needs to be returned for re-calibration due to the unique calibration system built in to the meter. Each time the meter boots up it automatically calibrates for optimum performance so you can align each install with confidence.
Remember to Register your me
The Digilent Cmod S6 is a small, 48-pin DIP form factor board built around a Xilinx Spartan 6 LX4 FPGA. The board also includes a programming ROM, clock source, USB programming and data transfer circuit, power supplies, and basic I/O devices. There are 46 FPGA I/O signals that are routed to 100-mil-spaced through-hole pins, making the Cmod S6 well suited for use with solderless breadboards. At just .7" by 2.6" inches, it can also be loaded in a standard socket and used in embedded systems.
The FPGA on the Cmod S6 can be configured in several ways - from a PC using the on-board Adept USB interface, from a stand-alone programming cable attached to the 6-pin JTAG connector, or from the on-board Quad-SPI Flash memory. Configuration files can be programmed using Xilinx's ISE 14.2 (or higher) development tools, using Digilent's Adept system, or using older versions of the Xilinx tools if Adept is also installed. Xilinx's ISE/Impact programming tool and Digilent's Adept tool will recognize the board and/or FPGA when the board is attached to a PC using a Type-A to micro-B USB cable.
Xilinx's iMPACT tool and Digilent's Adept can both be used to program the FPGA and on-board QSPI ROM. Please refer to the ISE and/or Adept documentation for more information on using the configuration software.