The VideoSecu MW390B is a full-motion TV wall mount for most 37"-70" LED LCD Plasma TVs. Constructed with high gauge steel, it handles screens up to 165lbs. This articulating mount supports TV with mounting hole patterns up to 24" horizontally, and 16" vertically (TV VESA 600x400, 600x300, 600x200, 500x300, 400x400, 400x300, 400x200, 300x300, 200x200, 200x100mm). Dual arm design allows 160 degrees side-to-side swivel (The max degree is depending on your display size), 15 degrees forward or 5 degrees backward tilt and extends the flat panel screen up to 25" from wall for perfect view positioning and reduce glare. The wall plate is 20.4" wide, allowing it to be mounted into two wood studs up to 19.6" apart. The rectangle cable management covers on the arm keeps the wire concealed and prevent pinching. Post installation level adjustment allows +/-3 degrees rotation for perfect level in different view angles. How to ensure the mount compliance with your selected display? First, the weight of your display should be less than 165lbs. Next, mounting holes distance on the rear of TV must be less than 24" (600mm) horizontally and 16" (400mm) vertically. Last, Your TV should be at least 37 inch. Otherwise, you will see the bracket. Notice: This mount fits most 37-60" TVs, some up to 65 70 inch TVs manufactured in recent 3 years
Fits most 37"-70" LCD LED plasma with VESA 200x200 300x200 300x300 400x300 400x400 500x300 up to 600mmx400mm
Adjustable 15 degrees tilt forward or 5 degrees backward; 160 degrees swivel from side to side (depend on the screen size)
Maximum weight capacity: 165lbs; +/-3 degrees rotation for level adjustment
Extension from wall: about 3" to 25"; Post-installation level adjustment allows the TV to perfectly level" to feature
Fit up to 19.6" stud; Cable management on arm. Standard hardware pack included
Product Information Specifications for VideoSecu Articulating TV Wall Mount Bracket for Most 37~70 inch Sony Samsung LG Panasonic Vizio Sharp LED LCD PLASMA, Full Motion Dual Arm pulls out up to 25" MW390B WTV Below:
The Falcon Folding Dish FLN-1 is neatest, most compact kit for the RV'er, camper, tailgater, and traveler that we offer. This simple solution will work with most every Directv receiver. Our kit comes with everything you need to get your satellite TV service on the road. All you need is your satellite receiver, your TV, and 120V power and you'll be ready to watch TV.
The Falcon FLN-1 is the first of it's kind that can be folded down and stores in a carrying case for later use!
With our exclusive How-to booklet, you'll have the kit up and going in no time.
This kit is compatible with all Directv receivers except: H25, HR34, Genie, C31, and C41. These receiver are SWiM compatible only.
Satellite Dish Mast Mount for Satellite Dish and Antennas
Lot of five,18 Universal mast The standard 1.66 OD satellite mast mount will work with Directv, Dish Network, and FTA satellite dishes with the same unting to vertical, horizontal, and pitches surface (wall, roof, diameter mount tube. Mount have a 90 degree range of motion for moetc.). Use for roof or sidewall mount for regular or large dishes.
38" J-Pole Antenna Mount Versatile all-in-one mount that can be used with antennas or satellite dishes. Can be mounted on the roof, wall, chimney or any other flat surface. J-pipe is reversible from mounting foot for a variety of positioning options. Gray weatherproof coating. Also available in shorter length
non penetrating foof mount satellite mount
This is the Non-Penetrating Roof Mount 2" for the Slimline Dish
2" Mast Diameter
Minor adjustment of mast pitch from 2 degrees positive to 10 degrees negative
Black powder coated steel construction
1.50" angle steel frame
Holds Eight concrete blocks for ballast
No roof drilling or roof penetration required
K.D. assembly allows easier portability to the roof.
This mount provides a 2.0" mast, the installer selects the diameter when assembling the frame. If the flat roof has a sleight pitch the mast can be adjusted from 2Â° outward from the frame to a little over 10Â° inward toward the block area.
No holes need to be drilled in the roof surface, this avoids reluctance by building owners and reduces the possibly of roof leaks. The total weight of the assembly can be varied by the use of either "light" concrete blocks or standard weight blocks.
Of course, this and ALL roof mounted antenna assemblies should be tethered to the building with a flexible steel cable for maximum security.